Specifications

  • Height: 332.7 mm / 13.10 in
  • Diameter: 781.1 mm / 30.75 in
  • Weight: 2.5 kg / 5.5 lbs
  • Max. Program Power: 30w
  • Maximum SPL: 87.0dB

Specifications

  • Dimensions: 53.2” x 28.3” x 21.7”
  • Low Frequency Limit: (-10 db): 25 Hz
  • Rigging and Handling: Flush-fitting 2-point rigging system; 6 ergonomic handles, 2 ground runners, 8 side runners
  • Weight: 174 lbs
  • Cabinet: Premium grade beech and birch plywood

Specifications

  • Maximum SPL: 136 dB
  • Low Frequency Limit: 32 Hz
  • Size: 29.5” x 21.3” x 27.8”

Specifications

  • 2-way Constant Curvature WST® enclosure 30° x 90°
  • Bandwidth: 55 Hz to 20 kHz
  • Maximum SPL: 135 dB
  • Power: LA4X amplifier

Specifications

  • 22.8" x 16.9" x 14.8"
  • 55Hz-20kHz (X15) preset
  • Maximum SPL: 136db
  • Nominal directivity: Vertical 60° Horizontal 40°
  • Monitoring Angle: 35° without risers, 55° with risers
  • Transducers: LF: 1 × 15” neodymium, bass-reflex, laminar vents HF: 1 × 3” neodymium compression driver, ellipsoid waveguide
  • Nominal Impedance: LF: 8 Ω, HF: 8 Ω
  • Connectors: IN: SpeakON®, LINK: SpeakON®
  • Rigging and Handling: 2 × handles DIN580-compatible M8 threaded insert 4 × M10 threaded inserts 2 × 35 mm pole sockets
  • 46.2 lbs
  • Cabinet: First grade Baltic birch and beech plywood
  • IP: IP43

Specifications

  • without 3rd party transmitter 9.9oz
  • 18 x 18 x 18 cm/ 7 x 7 x7 in.
  • Muting Circuit
  • Microphone Element: Electret condensor
  • Microphone Pattern: Omin Directional
  • 4 pin mini XLR (Shure)
  • 3.5mm Jack (Sennheiser)
  • 3 pin mini XLR (AKG)

Specifications

  • 106kg (234lbs)
  • 1342mm(52.8in) wide, 438mm(17.2in) high, 520mm(20.5in) deep
  • Bandwidth: 35Hz to 20kHz (-10dB)
  • Sampling Frequency: 96kHz

Specifications

  • Input channels: 72 mono, 8 Stereo
  • Busses: 24 mixes, 8 matrices (Input to Matrix supported)
  • Fader configuration: 16-fader left section, 8-fader centralogic section, 8-fader right section, 2-fader master section
  • Built-in meter bridge

Specifications

  • Mix channels: 16 mono, 8 stereo
  • Fader configurations: 16+2
  • 468mm(18.4in) x 272mm(10.7in) x 562mm(22.1in)
  • 135W
  • Busses: 16 mix, 8 matrix (Input to Matrix supported)
  • Signal Delay: Less than 2.5ms, INPUT to OMNI OUT, Fs=48kHz
  • Local I/O: 16 in, 8 out

Specifications

  • Internal: 44.1kHz/48kHz External: 44.1kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm), 48kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm)
  • +0.5, -1.5dB 20Hz-20kHz, refer to +4dBu output @1kHz, INPUT to OMNI OUT
  • Signal delay: less than 2.5ms, Input to Omni Out, Fs=48kHz
  • 21.8kg (48.1lb)
  • 828mm(32.6in) x 272mm(10.7in) x 563mm(22.2in)
  • Dynamic Range: 112dB typ.: DA Converter/108dB typ.: INPUT to OMNI out, input gain=Min.
  • 00-240V 50/60Hz
  • consumption: 200w
  • Crosstalk: -100dB*1, adjacent INPUT/OMNI OUT channels, Input Gain = Min.
  • Mix channels: 64 mono, 8 stereo
  • Busses: 16 mix, 8 matrix (Input to Matrix supported)
  • Local I/O: 32 in, 16 out
  • Fader configuration: 32 + 2 (Master)

Specifications

  • Produces a 110* Axi-symmetric directivity output
  • LA8 amplified controllers
  • Operates over a frequency range of 95Hz to 20kHz
  • 2 way passive design with a nominal impedance of 16 ohms

Specifications

  • Self-powered
  • Active 2 way live monitoring enclosure
  • 55Hz-22kHz bandwidth
  • Maximum SPL 125dB
  • 100* Axi-symmetric directivity output

Specifications

  • Each channel has an occupied bandwidth of 25kHz
  • Packs operate in the VHF Range which clears up valuable UHF spectrum for microphones and IEMs
  • Operate 30 base stations with up to 180 belt packs in the same UHF footprint as a 1 base station 4 beltpack system that uses traditional FM technology
  • UHF base to pack frequencies operate below allowed range of portable TVBDs
  • Up to 6 belt packs to one base station
  • Internal belt pack antennas
  • Audio quality of traditional FM intercom systems

Specifications

  • K2, full-range element, with adjustable horizontal directivity, operating from 35 Hz to 20 kHz
  • K1-SB, low-frequency element, reinforcing LF contour down to 30 Hz or LF throw down to 35 Hz
  • SB28, low-frequency element, extending the operating bandwidth down to 25 Hz
  • LA4X/LA8 amplified controllers or LA-RAK, touring rack fitted with three LA8

Specifications

  • Distributed masterless system architecture significantly reduces wiring and installation costs
  • Up to 1,024 x 1,024 non-blocking ports per system
  • A dual optical fiber ring forms a single large, full summing, non- blocking distributed matrix
  • Up to 128 intercom ports per matrix frame
  • Maximum distance between two nodes can be up to 500 m (1650 ft)

Specifications

  • Remote Control - Establishes a new-to-the-world capability in wireless microphones: comprehensive control of all transmitter parameters.
  • Spectrum Management - Designed to continuously monitor, evaluate, prioritize, queue and assign compatible UHF frequencies.
  • Wireless Workbench® 6 - Enhanced graphic user interface, tailored to support the breakthroughs in performance and networkability.
  • Frequency Diversity - Enables simultaneous transmission on two independent frequencies to ensure seamless, uninterrupted audio.
  • Interference Detection & Avoidance - Axient receivers can automatically detect interference and move to a clear, compatible frequency in a fraction of a second.

Specifications

  • High resolution 19” central touch screen
  • Twelve assignable “quick controls” (each with a rotary and three buttons)
  • 192 scalable I/O paths, at 96 kHz/24-bit flexible routing
  • 144 of the mix paths are full processing paths and 48 mix paths are dry
  • 32 VCA’s and ten Mute Groups
  • Channels have SSL’s studio grade SuperAnalogue™ mic preamps with 24-bit/96k Hz A/D D/A conversion
  • 36 x 36 matrix handles output routing to the PA system
  • Local I/O connectivity — analog XLR, AES-EBU digital, MADI coaxial/optical and USB) built into frame
  • Fader tiles can display up to five scrollable layers, with up to five vertical banks